7 mistakes of watering houseplants – how not to do it

Indoor plants need timely and proper watering. Each crop has its own characteristics and needs for the amount of moisture, which must be taken into account, otherwise the plants may die..

Consider the most common mistakes made when watering indoor flowers.

Water only from above

Overhead watering is possible, but not suitable for all plants. Top watering is contraindicated for some varieties of cacti – it is undesirable for them to wet the caudex. Some indoor plants do not like moisture on the leaves – violet, hibiscus. In addition, overhead watering is extremely inconvenient for plants with a wide crown – the water spreads in different directions past the pot.

How to do it right

It is necessary to choose its own watering method for each plant..

The top method is suitable for bulbous flowers – this is how water enters the top layer of the soil and is gradually distributed from top to bottom, without stagnating at the roots.

Watering from the bottom is suitable for cacti and violets (submersible method) – this way the root system will receive the required amount of moisture, while the upper part of the plant will be dry.

Use running cold water

One of the most common mistakes is moistening indoor flowers with cold tap water (this is especially common in hot weather). This error can be fatal for delicate indoor flora:

  • Cold water will provoke a shock state for the root system..
  • Such watering cools the soil too much, which can slow down the growth and development of the plant..
  • The presence of cold water in the soil (especially its excess) can cause rot on the roots.

How to do it right

Use room temperature water.

Plants do not need to be cooled with cold water in the heat – this is pointless. As a rule, if it is too hot and the plants need more moisture, they need to be watered more often. Spraying or drafts are suitable for some varieties.

Strictly follow the watering schedule

A frequent occurrence – indoor flowers are watered clearly on schedule. Over time, the plants begin to ache, dry out or wither, and the wrong distribution of moisture is to blame..

The location of the flower also affects. For example, a flower located near a heating radiator or on a windowsill on the south side will require much more water than a flower standing on a desk in a cool walk-through room.

How to do it right

It should be understood that each flower has its own needs, and they differ significantly from each other. How to calculate watering correctly:

  • It is necessary to find out the need for water for each flower.
  • Monitor the condition of the soil – water each plant as needed.
  • Do not water if it is “on schedule”, but the ground is still relatively wet.

Pay attention to the plant. If the stems and leaves become lethargic, the color fades, and the soil in the pot is completely dry – the flower is thirsty.

Same watering frequency throughout the year

Even if the apartment is constantly kept at the same temperature, it is still necessary for plants to adjust the frequency of watering depending on the season. The same watering throughout the year negatively affects the development and flowering.

How to do it right

Water according to the biological cycle.

All representatives of flora (and not only domestic ones) have a biological cycle. Winter is a period of slowing growth, so moisture needs to be reduced. Summer and spring are an active growth phase, so more abundant watering is needed.

Using warm or hot water

It is believed that if it is cold in the apartment or the plant was brought from the street, where it was carried in the cold, it needs to be heated. Heating means warm or hot water, which needs to be watered.

This absolutely must not be done. After being in the cold for a short time, the flowers will survive, and if you fill them with hot water, it will destroy the roots. A strong temperature drop, especially hot water after frost, is autumn, a strong shock for the plant, leading to rapid decay of the root system. As a rule, this is a fatal error that can cause the flower to die quickly..

How to do it right

Drizzle with water at room temperature.

In general, try not to create sudden temperature changes for capricious indoor flowers – this is a shock for the plant in any case..

The remaining water in the pan after watering is needed by the plant

It is believed that the tray was created for this – to hold water for the plant, feeding it with moisture. This is a misconception – stagnant moisture can lead to decay of the root system, the appearance of mold and fungal diseases..

How to do it right

Always drain the sump in a timely manner. It is better to water moisture-loving plants more often, without creating stagnant water..

Too much watering

Absolutely all plant crops need a certain amount of moisture. You can not water plants according to the principle “the more water – the healthier and better”.

Too much water in a pot of indoor flowers can cause white mold, which is a significant hazard. If you notice mold on flowers, a sluggish and soft stem of a plant, withered leaves with traces of rot – this is already a big problem due to excess moisture.

How to do it right

You can try to save the plant. Methods:

  • Remove it carefully from the pot.
  • Clean it, if there is mucus – disinfect.
  • Place on absorbent dry paper (kitchen towels, etc.).
  • Do not squeeze the roots – let everything dry naturally.
  • Leave to dry for 8-12 hours.
  • Try planting again – in new soil and a different pot.
  • Don’t pour so hard anymore.

Water your indoor flowers correctly and based on their preferences. Moisture-loving crops can suffer from an excess of moisture no less than drought lovers from a lack of moisture.

When watering, it is important to maintain a balance in relation to all indoor representatives of the flora – and they will thank you with lush flowering and aesthetic appearance..